Visit stages and preparation checklist Faults and repairs

Electrical Fault Finding in Cirencester: Next Steps

How electrical fault finding works: the stages of a visit, what to have ready and what UK guides say it costs, with VAT noted, for Cirencester homes.

Electrical fault finding is a staged job, not a guess: the circuit is made safe, the electrician works out where the fault sits, the repair is quoted, and the work is tested afterwards. Published UK guides put the diagnosis visit at roughly £80 to £200 including VAT, with the repair priced separately. That is a market range from other publishers, not a JI Electrical price, and none of it is specific to Cirencester.

This guide reflects the HSE, IET, NICEIC, Electrical Safety First and cost-guide pages opened on 6 November 2026. It is written for homes in Cirencester and the Cotswolds, but the steps apply anywhere in England. It is general information, not a diagnosis of your wiring. If you can smell burning or see smoke, skip the guide and read the first section.

If something is wrong right now

The IET says that a burning smell, excessive heat, smoke, burning or charring means you should isolate the installation immediately and then consult a registered electrical contractor. NICEIC adds that buzzing, scorch marks, melted plastic, a hot or sparking socket or any electric shock, however minor, are reasons to stop and call a registered electrician straight away. If there is fire or smoke, leave the building and call 999.

For the common, less urgent case, a switch that keeps dropping or a socket that has gone dead, our guide to why electrics keep tripping has the unplug, reset once and test-the-appliances routine. Come back here when that routine has not solved it, because that is the point at which the IET says a registered contractor should test the installation and diagnose the fault.

What a fault-finding visit involves, stage by stage

The pages that sell this service describe it in one or two lines. The table below sets out the stages that the opened sources actually support, and says whose words they are. It describes the general method, not how any one firm works. Where a source is silent, the row says so.

StageWhat happensSource
1. Questions and a look roundThe electrician asks what happened and when, then inspects the reported problem, which includes a visual check and looking at the consumer unit for tripped breakers or blown fusesFantastic Services describes a visual inspection and a consumer unit check
2. Make the circuit safeThe circuit is securely isolated and the conductors are proven dead with suitable test equipment before anyone works on them. An RCD does not replace isolationHSE electricity FAQ
3. Test to narrow it downInstruments such as insulation testers and multimeters are used to find which circuit, cable or accessory has failed. Insulation resistance readings give an indication of the condition of the insulation on conductors and connected equipmentFantastic Services (instruments); NICEIC via Voltimum (insulation resistance)
4. Account for equipment that skews the resultSurge protective devices, dimmers, electronic switches and RCDs can affect insulation readings, so they may need to be disconnected or the test voltage reducedNICEIC via Voltimum, 2016
5. Name the cause and quote the repairThe cause is recorded and the repair is priced. Fantastic Services says repair and parts are usually quoted separately and that the diagnostic fee may be deducted if you go aheadFantastic Services
6. Check it worksAfter the repair, a final set of checks confirms the circuit is sound. How these are recorded is not described in the opened sourcesFantastic Services (final checks only)

Two points stand out. First, the HSE is clear that live working is a last resort: its FAQ says it is never absolutely safe to work on live electrical equipment and that live work is only allowed once it has been decided that it is unreasonable for the job to be done dead. A fault-finding visit is therefore mostly about working methodically on dead circuits. Second, the NICEIC insulation-testing guidance was written for verifying circuits and dates from 2016, so it explains why disconnecting sensitive equipment matters rather than setting a fault-finding procedure. We have not claimed more than that.

Control panel in a timber shelter with labelled ways, a main switch and thick armoured cables coming in from below
A labelled control panel from JI Electrical's project photographs. Labelled ways are what let a fault be narrowed to one circuit; this is not a fault job.

What to have ready before the electrician arrives

An intermittent fault is hard to find from a cold start, so the best help you can give is a clear record. None of the opened sources publishes a time saved by doing this, so treat it as common sense rather than a promise.

  1. 1
    Which switch, which circuit

    NICEIC says to look for the switch sitting in a different position from the rest. Note which one it is and what it seems to feed, such as sockets downstairs or the kitchen lights.

  2. 2
    When and what was running

    Write down the time, the weather if it was wet, and what had just been switched on. Overloading several high-powered appliances on one extension lead is one of the causes NICEIC lists.

  3. 3
    Which appliance, if any

    The IET says a trip is usually caused by a faulty appliance rather than the installation. Say whether you unplugged everything and whether a particular item brought it down. Keep that item out of use.

  4. 4
    A photograph of the front of the board

    Take it with the cover closed. You only ever need the switches on the front, and the photograph shows the age and layout of the board without anyone opening it.

  5. 5
    Any earlier paperwork

    An earlier EICR or certificate for recent work tells the electrician what was last tested. Electrical Safety First recommends an inspection every five years for rented homes and every ten for owner-occupied homes.

Do not try to repair loose or damaged wiring yourself. NICEIC says you should not, and a socket that has stopped working may still be live. The IET also warns that repeatedly resetting a breaker or RCD on a fault could damage the device, so one reset to learn something is reasonable and ten is not.

Before you book a visit

Ask what the first fee covers.

A clear quote says what the call-out includes, the hourly rate after it, VAT, and whether the diagnostic fee comes off the repair.

Ask for a quote
Call 07380 944864

What published guides say fault finding costs

Two UK guides were opened with usable figures. They treat VAT differently and describe different things, which is why a single average is not useful. Prices are for the diagnosis; neither guide treats the repair as part of it.

What is pricedPublished rangePublisher and what it says
Typical diagnosis visit£80 to £200Fantastic Services, 2026 (no exact date). Says its figures include VAT
Call-out and first diagnostic hour, rest of the UK£80 to £150Fantastic Services. Includes VAT
Extra diagnostic time, rest of the UK£40 to £70 an hourFantastic Services. Includes VAT
Complex or intermittent fault, rest of the UK£150 to £250 or moreFantastic Services. Includes VAT
Emergency or out-of-hours call-out, rest of the UK£150 to £300Fantastic Services. Includes VAT
Troubleshoot and diagnose a faultAbout £95Hamuch, last updated 12 August 2022. Its regional averages exclude VAT and call-out charges; the source of its data is not stated

Read these as a spread, not a quote. The two publishers do not say how they gathered their figures, the Hamuch page is more than four years old, and its headline figure leaves out call-out charges, which is usually where a visit starts. Fantastic Services says the repair is quoted separately, so a low diagnosis price tells you nothing about the total. It also says a fault-finding visit does not include a full EICR or a consumer unit replacement.

That last point is worth keeping. Fault finding looks for one problem. An EICR, by contrast, is a periodic inspection of the whole fixed installation, which Electrical Safety First says is meant to check whether it is safe for continued use. If a visit uncovers wider concerns, an EICR may follow, but it is a separate job and a separate price. Our EICR cost guide and call-out charges guide explain the difference in fees.

Locked white sub-board on strut channel against a steel wall, cables entering at the top and a double socket below
A sub-board with a double socket beneath it, from JI Electrical's project photographs. Shown for the board and socket, not as a repair.

Questions that make two quotes comparable

  • What does the call-out fee include? Travel, the first hour, and any testing equipment, as one guide implies, or only the journey.
  • What happens after the first hour? Ask for the hourly rate and whether a cap or a check-in applies before the time runs on.
  • Is VAT included? The two guides above disagree on this, so ask for it in writing.
  • Is the diagnostic fee deducted from the repair? Fantastic Services says it may be; do not assume.
  • What paperwork do I get? Ask what is recorded after the repair and whether a certificate applies. The Part P guide covers when notifiable work needs one.

If the fault turns out to be the board itself, the choice is usually repair or replace. See the signs a fuse box needs replacing, what the RCD rules require and consumer unit replacement costs. For landlords, an unexplained fault in a rental is a reason to check the renewal date in how long a landlord EICR lasts. If you are weighing who to call, seven checks before choosing an electrician applies to a small fault as much as a big job.

Booking Jack for a fault

JI Electrical is a Cirencester firm run by Jack Innes, covering domestic electrical work, EICRs and rewires. When you contact Jack about a fault, send the notes from the checklist above, the photograph of the board and the age of the property. Ask for the diagnosis price in writing, what the first visit covers and what happens next if the fault is bigger than expected, so the quote can be read against the questions above.

Customer reviews

What customers say about Jack

Jack did a great job installing new spotlights in our kitchen. He turned up on time, worked efficiently, and everything was finished to a really high standard.

Alex RGoogle review

Jack and his colleague Freddie arrived on time, worked efficiently, and everything was completed to a really high standard. The price was fair and they left everything clean and tidy afterwards.

Finley ThompsonGoogle review

I contacted JI Eletrical within 24hrs with an issue and they came to fix it quickly and not had a problem since!

Milly PotterGoogle review

Read more Google reviews

Electrical fault finding questions

What is electrical fault finding?

It is the process of locating why a circuit, socket or light is not working or keeps tripping. The sources opened describe isolating and proving the circuit dead, testing with instruments to narrow down the cause, quoting the repair and checking the result.

How much does electrical fault finding cost?

Fantastic Services gives about £80 to £200 including VAT for a diagnosis visit, and Hamuch gave about £95 excluding VAT and call-out charges in 2022. The repair is priced separately. These are market ranges, not a JI Electrical price.

Is fault finding the same as an EICR?

No. Fault finding looks for the cause of one problem. An EICR is a periodic inspection of the whole fixed installation, and Fantastic Services says a fault-finding visit does not include one.

What should I do before the electrician arrives?

Note which switch moved, when it happened and what was running, keep any suspect appliance unplugged and photograph the closed consumer unit. Do not open the board or repair wiring yourself.

When is a fault an emergency?

The IET says a burning smell, excessive heat, smoke or charring means isolating the installation immediately and consulting a registered electrician. If there is fire or smoke, leave and call 999.

How do I book Jack Innes for an electrical fault?

Use the contact page or call 07380 944864. Send the circuit, the symptoms and a photograph of the closed board, then ask for the diagnosis price and what the first visit includes in writing.

Sources checked on 6 November 2026

The cost figures are other publishers' market ranges. They are not a JI Electrical price.

An electrical fault at home

Send Jack the details.

Include the circuit, when it happens and a photograph of the closed consumer unit, and ask whether he can look at it.

Ask for a quote Call 07380 944864 Ask Jack about an electrical fault