If a socket smells of burning, stop using it and switch off the circuit it is on at the consumer unit. If you cannot tell which circuit that is, or the smell is strong, switch off the whole installation. Then ask a registered electrician to look at it before anything is plugged in again. A smell that fades is not a sign the problem has gone, because the heat that caused it may simply have eased for now. If there is smoke or flame, leave the building and call 999.
This guide reflects the IET, NICEIC, two fire and rescue services and Electrical Safety First pages opened on 9 November 2026. It is written for homes in Cirencester and the Cotswolds, but the steps apply anywhere in England. It is general guidance, not a diagnosis of your wiring, and it does not replace an electrician looking at the socket.
The first few minutes, in order
The IET says that if a burning smell is noticed, excessive heat or smoke is detected, or there is evidence of burning or charring, the installation should be isolated immediately and without delay, and a registered electrical contractor consulted for further advice. NICEIC lists the same group of signs for a socket and says to call a registered electrician immediately. The steps below put those instructions in an order you can follow while you are worried.
- 1Leave the socket alone
Do not press the plug in, jiggle it or test it with another appliance. If the plate looks scorched, melted or feels hot, do not touch it with bare hands.
- 2Switch off at the consumer unit
Turn off the breaker for that circuit. If you do not know which one it is, or the smell is strong, use the main switch. Switching off at the unit also stops the circuit feeding the socket, which unplugging alone does not.
- 3Unplug the appliance only if it is safe to do so
Once the circuit is off, remove the plug and look at its pins. Blackened or melted pins are worth telling the electrician about. Do not use that appliance again until it has been checked.
- 4Leave the circuit off and make the call
Keep the breaker off until a registered electrician has seen it. Say what you smelled, where, what was plugged in and whether you saw marks.
- 5Get out if it escalates
Smoke, flame or a spreading smell mean leave, stay out and call 999. Do not go back for belongings.
Step 2 follows the IET instruction to isolate. The fine detail of which switch to use is a practical judgement: the sources do not say whether to use the circuit breaker or the main switch, so use the main switch if you are unsure.
Signs that mean stop, and who says so
A burning smell is the headline, but it is rarely the only clue. The table sets out the warning signs the opened sources list, and says whose words they are. All of them point the same way: stop using it and get it checked.
| What you notice | What the sources say to do | Source |
|---|---|---|
| Burning smell or buzzing from the socket | Call a registered electrician immediately | NICEIC, 19 August 2026 |
| Scorch marks, discolouration, melted plastic or smoke | Call a registered electrician immediately. The IET adds that evidence of burning or charring means isolate at once | NICEIC; IET |
| Socket, plug or wall around it feels hot | Call a registered electrician immediately | NICEIC |
| Sparking, crackling or unusual noises | Call a registered electrician immediately | NICEIC |
| Any electric shock, however minor | Call a registered electrician immediately | NICEIC |
| Burn marks on plugs or sockets, arcing, fuses blowing or breakers tripping | Have a registered electrician check the electrics as soon as possible | Electrical Safety First |
| Hot plugs or sockets, scorch marks, fuses that often blow | Possible signs of a bad connection; flickering lights can also point to loose wiring | Essex County Fire and Rescue Service |
| Smell of hot plastic or burning, blackness or scorch marks around a plug or socket, melted plastic on plugs | Do not use devices with obvious damage such as frayed cables, exposed wires or melted plastic | Buckinghamshire Fire and Rescue Service |
Two things to notice. The fire services are describing signs to check for regularly, not giving a diagnosis, and NICEIC is describing a plug socket that is failing, not a fire. Treat the wording as a prompt to act, not a measure of how bad the fault is. A hot plate with no smell still counts.

What may be behind it, and what the sources do not say
Nobody can tell you the cause from the smell. A registered electrician has to look. The opened sources point to two broad families, and it helps to keep them apart because one is a fault and the other may be a habit.
A loose or damaged connection
NICEIC says that over time wiring can become loose or damaged, which can lead to a loss of function, and that you should not try to repair damaged or loose wiring yourself. Essex Fire and Rescue lists hot plugs or sockets, scorch marks and fuses that often blow as signs of loose wiring or other electrical problems. A commercial electrician’s page, The Lady Sparky, makes the further point that a loose cable can overheat and melt its insulation, producing a burning smell. That page is an electrician’s own advice for a consumer unit, cites no outside sources and has no date, so we have used it only as a plain statement of the mechanism and not for any figure.
Too much load on the socket
Buckinghamshire Fire and Rescue says not to overload a socket by plugging too many appliances into an extension lead, that most extension leads are rated at 13A but some are rated at 10A or less, and that overloading an extension lead could cause the plug in the wall socket to overheat and possibly cause a fire. Essex Fire and Rescue records a house fire in Clacton-on-Sea on 8 April 2025 caused by an overloaded extension cable powering a vivarium, and advises one adaptor per socket and not plugging adaptors into each other.
If you were running a heater, a kettle or several chargers off one extension lead when you noticed the smell, say so. It does not mean the socket is fine. Heat that built up in the plug and socket may have left damage behind, so the check is still needed.
What none of the opened sources gives is a rule that lets you decide at home which of the two it is. That is the point of the electrician’s visit.
Before you call
Have your notes ready.
Room, time, what was plugged in, which breaker you switched off and a photograph taken with the circuit off make the first conversation shorter.
Ask for a quoteCall 07380 944864
What not to do
- Do not keep resetting a breaker that trips. Electrical Safety First says an RCD that keeps tripping is likely to mean a fault in an appliance or the wiring that a registered electrician should investigate. If a breaker will not stay on after a burning smell, leave it off.
- Do not open the socket or the consumer unit yourself. NICEIC says you should not try to repair damaged or loose wiring. The Lady Sparky page also advises against opening the board cover because live parts may remain even with the main switch off.
- Do not just swap the faceplate and carry on. We could not find a UK primary source on whether a new faceplate is enough, so we have not claimed either way. Heat damage can be inside the back box or along the cable, which only an electrician can check.
- Do not plug the appliance in elsewhere on an extension lead. Moving it does not tell you whether the first socket is safe. Leave the affected socket unused until it has been checked, and follow the fire services’ advice of one adaptor per socket.
- Do not wait for the smell to come back. The IET instruction is to act when the smell is noticed.
If the smell was around the consumer unit rather than a socket, the same steps apply, and our guide to the warning signs that a fuse box needs replacing explains what else to look for on the board.
What to tell the electrician when you call
An intermittent fault is hard to find from a cold start, so the best help is a clear record. None of the opened sources publishes a time saved by doing this, so treat it as common sense, not a promise.
- Where and when: which room, which socket, what time and whether it happened once or more than once.
- What you smelled and saw: burning plastic, fishy or acrid, any discolouration or melting, any noise.
- What was plugged in: the appliance and whether an extension lead or adaptor was involved.
- What you did: which breaker you switched off, and whether you unplugged anything or touched the socket.
- A photograph: of the socket and plug, taken from a safe distance with the circuit off, and of the closed consumer unit.
- Paperwork: the date of the last EICR and any recent certificate. Electrical Safety First says tenanted homes should be inspected every five years or at each change of occupancy, and owner-occupied homes at least every ten.
Our guide to how electrical fault finding works explains the stages of the visit that follows, and call-out charges in Cirencester explains why the first fee varies. Neither is a quote for this job, and nothing here is a JI Electrical price.

After the electrician has been
If the cause was a worn socket or a loose termination, the repair may be small, but the opened sources do not say what a visit costs or how long it takes, so ask for both in writing. If the problem was a socket that is overloaded in daily use, the Buckinghamshire Fire and Rescue advice is to consider having extra sockets installed by a qualified electrician if you regularly rely on extension leads and adaptors. Our extra sockets guide and outdoor socket guide explain scope and market ranges, again as other publishers’ figures and not a JI price.
If it happens again, or the breaker will not stay on, ask whether a wider check is sensible. That would be a periodic inspection of the whole installation, not a repair, and the EICR cost guide and landlord EICR guide explain what one covers. If you rent the property, tell your landlord or letting agent. Landlords may also want how long a landlord EICR lasts. If trips are the main symptom, start with why electrics keep tripping, and if you are weighing who to call, seven checks before choosing an electrician applies to a small job as much as a big one.
Asking Jack about a socket
JI Electrical is a Cirencester firm run by Jack Innes, covering domestic electrical work, EICRs and rewires. If you want to contact Jack about a socket, send the notes above and the photographs, and ask whether he can look at it, how soon, and how the visit would be charged. Ask for the price and what it includes in writing, and ask what happens if the cause turns out to be bigger than the socket. See also the lighting, power and alterations page for the sort of work Jack lists. If there is smoke, flame or a spreading smell, do not wait for a callback: leave and call 999.
Customer reviews
What customers say about Jack
Jack did a great job installing new spotlights in our kitchen. He turned up on time, worked efficiently, and everything was finished to a really high standard.
Jack and his colleague Freddie arrived on time, worked efficiently, and everything was completed to a really high standard. The price was fair and they left everything clean and tidy afterwards.
I contacted JI Eletrical within 24hrs with an issue and they came to fix it quickly and not had a problem since!
Burning smell from a socket questions
What should I do if a socket smells of burning?
Stop using it, switch off the circuit at the consumer unit (or the main switch if unsure) and ask a registered electrician to look before it is used again. The IET says a burning smell, excessive heat or smoke means the installation should be isolated immediately.
Is a burning smell from a socket an emergency?
NICEIC says to call a registered electrician immediately for a burning smell, scorch marks, a hot or sparking socket or any shock. If there is smoke or flame, leave the building and call 999.
The smell has gone. Is the socket safe?
Not necessarily. None of the opened sources says a fading smell shows the cause has cleared, and the IET instruction is to act when the smell is noticed. Keep the circuit off until an electrician has checked it.
Can overloading an extension lead cause a burning smell?
Buckinghamshire Fire and Rescue says overloading an extension lead could make the plug in the wall socket overheat and possibly cause a fire, and that most leads are rated at 13A, with some at 10A or less. It still needs checking.
Can I replace the socket myself?
NICEIC says you should not try to repair damaged or loose wiring yourself. Heat damage may be behind the faceplate, so have a registered electrician look at it.
Does Jack charge for looking at a socket?
This guide does not state a JI Electrical price. Ask Jack whether he can look at it, how soon and how the visit is charged, and ask for the price in writing.
Sources checked on 9 November 2026
Sources not opened: none cited from snippets. This is general guidance, not advice on a specific installation, and no figure here is a JI Electrical price.
- IET: consumer units, consumer guidance
- NICEIC: plug socket not working, these could be the reasons why (19 August 2026)
- Buckinghamshire Fire and Rescue Service: electrical safety
- Essex County Fire and Rescue Service: house fire caused by overloaded extension cable (8 April 2025)
- Electrical Safety First: your questions answered
- The Lady Sparky: burning smell from a fuse board (undated electrician’s page)